Weve Run Into a Problem Try Again Øâ®ã˜â·ã˜â§
KB ID 0001132
Below is not an exhaustive list of connexion errors, information technology's just a some things that take tripped me up. If yous have a nasty error that you have fixed, feel free to drib me a line, send me some screenshots and the fix, and I'll add them besides.
General Errors
Remote Desktop tin't connect to the remote figurer for one of the following reasons;
1) Remote access to the server is not enabled
ii)The remote computer is turned off
3)The remote computer is not available on the networkBrand certain the remote computer is turned on and connected to the network, and that remote access sis enabled.
Probably the nigh mutual (and easiest to troubleshoot) of RDP errors, firstly ensure that the server is actually 'listening' for RDP connections, on the SERVER consequence the post-obit command;
netstat -an | observe /i ":3389"
You should meet it LISTENING (Note: Below its listed twice considering its listening on IPv4 and IPv6)
If its not, the the service might not even be running, Wait in Services, and ensure the following services are running;
- Remote Desktop Services
- Remote Desktop Services UserMode Port Redirector
Make sure that RDP has been allowed on the local firewall of the RDP server, In the past I've seen a bug on some versions of Windows when even with the firewall disabled, things didn't work unless RDP was allowed on the firewall settings. (I know that makes no sense, but I've seen it, especially for remote VPN traffic).
Test RDP Connectivity
From a machine ON THE Same NETWORK as the target RDP Server, firs meet if yous can ping the server past both IP address and hostname. (This is more than for peace of mind remember the server might ot respond to pings but might be responding to RDP Traffic.
And so test that the machine you are on can get to the the RDP server on the correct port, (TCP 3389*)
Test-NetConnection {IP-Address-or-Hostname} -Port 3389 OR Examination-NetConnection {IP-Accost-or-Hostname} RDP 
Providing this works, now try the Same tests form outside you network, i.east. exterior the firewall, or on a remote VPN connection etc.
*RDP Port Note: Commonly RDP is on TCP 3389, check on the server just in case someones changed the RDP listening port number. Or the firewall is expecting you lot to connect on another RDP Port.
Your computer tin can't connect to the remote calculator because an error occurred on the remote computer that y'all desire to connect to. Contact your network ambassador for assistance.
Solution for Windows x: I struggled with this for a while, all forum posts refer to windows vii/viii and the problem was caused past a windows update (KB2592687), that needed to be removed. Only I was connecting with Windows 10? This was the resolution;
Create/Edit a 32 bit DWORD value called RDGClientTransport in your registry at;
HKCU > SOFTWARE >Microsoft > Terminal Services Client
Set its value to '1' (one).
Too Come acrossRemote Desktop Spider web Access – Connectedness Error
Your computer can't connect to the remote computer considering your computer or device did not pass the Network Admission Protection requirements prepare by your network administrator.Contact your network administrator for assistance.
Y'all normally see this mistake if one (or more), of your Remote Desktop Role servers does not accept the right document installed on information technology, (or the document it does has has expired).
Server Director > Remote Desktop Services > Drove > Task > Select your collection > Task > Edit Deployment Settings > Certificates > Check and reinstall each 1 as required.
Remote Desktop Gateway Errors
Your reckoner can't connect to the remote computer because the Remote Desktop Gateway server accost is unreachable or wrong. Type a valid Remote Desktop Gateway server address.
Your reckoner can't connect to the remote figurer because the Remote Desktop Gateway server is temporarily unavailable. Endeavour reconnecting later or contact your network administrator for assistance.
The auto trying to connect needs to be able to resolve the 'public name' of the Remote Desktop Gateway server. And this may not be the hostname of the server! As you can see in the prototype above the Gateway server name is ready to rdg.smoggyninja.com. The important matter is when I ping this name, it resolves to the correct IP address, (mine responds to pings, yours probably wont if you lot're connecting though a firewall.)
In some cases you need to set the public proper name of the the Remote Desktop Gateway server, in the servers IIS Settings. On the Gateway server > Beginning > Administrative Tools > Internet Data Services (IIS) Managing director > {Server-name} > Sites > Default Website > RDWeb > Pages > Application Settings > Set 'DefaultTSGateway' to the public name of the gateway server. Then from command line run ' iisreset ' to restart the web services.
Your calculator can't connect to the remote reckoner because the Remote Desktop Gateway server'south certificate has expired or has been revoked. Contact your network administrator for assistance.
In nigh cases this should be easy to fix, if you lot use self signed certificates make sure your CRL settings and/or OCSP settings are right. If you use a publicly signed cert make sure your client tin contact the publishers CRL (expect on the backdrop of the certificate).
Check the Obvious: It maxim the RDG cert has expired, make certain it's in date! In the Gateway Server Launch Server Manager > Remote Desktop Services > Collections > {Collection-proper noun} > Tasks > Edit Deployment Properties.
Certificates > RD Gateway > View Details > Is it in appointment?
Everything is OK? Simply I'g Still Getting This Error?Are y'all publishing the Gateway with something else like Web Application Gateway? Threat Management Gateway? Load Balancer? Look in that direction.
Also SeeRemote Desktop Spider web Access – Connexion Error
Related Articles, References, Credits, or External Links
NA
Source: https://www.petenetlive.com/KB/Article/0001132
0 Response to "Weve Run Into a Problem Try Again Øâ®ã˜â·ã˜â§"
Post a Comment